Our expert technicians can fix many brands of handheld power tools and also outdoor power equipment and breath life into your old tools.
All tools will be charged an initial diagnostic fee. Once the tools have been diagnosed if the repair is approved this will be applied to the cost of the repair. Assembled unrepaired tools are unsafe and potentially dangerous. Any tools left not picked up 60 days from the date of the diagnostic or completion of the tool will be considered abandoned and will be recycled accordingly.
If warranty work is needed, please contact us with brand and model number prior to sending in your tool/equipment

We test many different brands of torque wrenches as well as torque multipliers.

Should I wind my Torque Wrench Back to Zero?
For those looking for a simple answer to the question posed, the default period of use between recalibrations is 5000 cycles or 12 months. However, the standard recognizes that many businesses will have their own procedures for the control of test devices and, as a torque wrench can be considered a test device, a company’s own procedures must take precedence over the default 5000 cycles/12 months.

We are able to calibrate all types of torque equipment to manufacturer standards, giving you the confidence to know that your device is generating accurate measurements each and every time you use it.
It is important to regularly ensure that your torque devices are displaying accurate results, and performing the calibration process makes sure that the readings of your device are accurate to a set standard. Our team is able to assess a large selection of torque equipment and make adjustments as necessary to revert the equipment back to the standard measurement range. If calibration isn’t performed, general wear and tear can have an effect on the internal workings of the device, ultimately leading to incorrect readings every time the torque device is used.

Equipment Type: Chain Fall | Inspection Frequency Required: Annual | Primary Governing Body: ANSI
We repair manual, electric, lever, and pneumatic chain hoists as well as cable pullers up to 15 tons, pick-up and delivery can be arranged. We can also re-certify your hoists and pullers in compliance with OSHA regulations.

Hoist Maintenance and Inspection

Chain hoists are durable and long lasting. The only regular maintenance is inspection, cleaning and lubricating. Chains should be kept clean and rust free. There are only a few bearing points that require oiling but these often require dismantling the hoist. Depending on the use we recommend this should be done annually. Since these devices have gears it is important to keep them clean and grit/sand free. To clean the gears requires dismantling and afterward greased with appropriate lube. Afterward, we load test them and supply you with a certificate that you will need for any health and safety inspections and supply you with a warning tag.

With regular annual inspections of permanent lifting magnets, you will prevent injuries on workplaces and ensure all health and safety regulations are met.
For safety reasons we recommend the permanent lifting magnet tests to be carried out annually.

Lawn mowers - Get ready for the lawn mowing season. A preventative maintenance check-up is recommended annually we service all makes and models. Our expert technicians go through your entire lawn mower to make sure it is ready when you need it if any parts need to be replaced we will let you know. The tune-up includes an oil change, checking spark plugs and sharpening blades etc.

Snow Blowers – we repair and service all makes and models of snow blowers. Again we recommend and annual preventative maintenance check-up so it’s ready when you need it this includes and oil change and tune-up.

We recommend and annual check-up before using again when it has been sitting for a while. This includes cleaning carburetor, air filter, spark plug, oil change etc. If it does need parts replacing we will let you know, we can also do engine rebuilds if necessary.

We recommend making sure that your air tools are oiled daily or after each use and that you are using a clean air line/supply. An annual check-up is recommended, we check for worn vanes, o-rings, and gaskets etc. and re-lube as necessary.

This includes Crimpers, Floor Jacks, Bottle Jacks, Transmission Jacks and Under Axle Jacks, Hand pumps, Underwater impacts and Jack Hammers we repair them all. An annual check-up is recommended for the seals, gaskets, hydraulic lines and internal components

We service all makes and brands of Air Compressors if it is too large to bring to us we can come to you, call to schedule a service call. An annual check-up is recommended.

We recommend and annual check-up before using again when it has been sitting for a while. This includes cleaning carburetor, air filter, spark plug, oil change etc. If it does need parts replacing we will let you know, we can also do engine rebuilds if necessary.

If you have equipment that is too big to bring you can arrange to have an experienced service technician to come to your location.

We recommend and annual check-up before using again when it has been sitting for a while. This includes cleaning carburetor, air filter, spark plug, oil change etc. If it does need parts replacing we will let you know, we can also do engine rebuilds if necessary.

We repair and service all brands of Magnetic Drills.